View SKY65116_4466015.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

data sheet
SKY65116: 390-500 MHz Linear Power Amplifier
Applications
l l l l l
TETRA radio GSM450 and GSM480 NMT450 Wireless local loop UHF TV broadcast
all the active circuitry in the module. This includes the in-module bias circuitry, as well as the RF interstage matching circuit. The input and output match is realized off-chip within the module package to optimize efficiency and high power performance (P1 dB = 32.5 dBm) into a 50 W load. Primary bias to the SKY65116 can be supplied directly from a single cell lithium-ion or other suitable battery with a nominal output of 3.6 V. No external supply side switch is needed as typical "off" leakage is a few microamperes with full primary voltage supplied from the battery. The module can operate over the temperature range of -40 C to +85 C. A populated evaluation board is available upon request.
Features
l l l l l l l l l l l l
Wideband frequency operation: 390-500 MHz High linearity: OIP3 43 dBm High efficiency: 40% PAE High gain: 35 dB P1 dB = 32.5 dBm Single DC supply: 3.6 V Internal RF match and bias circuits PA on/off voltage control Operating temperature -40 C to +85 C Available on tape and reel Low cost MCM 12-pin (8 x 8 mm) package Available lead (Pb)-free and RoHS-compliant MSL-3, 260 C per JEDEC J-STD-020
Block Diagram
VCC1 VREF VCNT VCC2
Active Bias
RF In
Input Match Stage 1
Interstage Match Stage 2
Output Match
RF Out
VCNT
12 GND 1
11
10 9 GND RFOUT
Description
The Skyworks SKY65116 is a fully matched, 12-pin, 8 x 8 mm2, surface mount multi-Chip module (MCM), linear Power Amplifier (PA), high linearity and high efficiency surface mount module designed for use in the 390-500 MHz band. The device is fabricated using Skyworks high reliability Gallium Arsenide (GaAs) Heterojunction Bipolar Transistor (HBT) process, which allows for single supply operation while maintaining high efficiency and good linearity. Microwave Monolithic Integrated Circuits (MMICs), comprised of GaAs and Silicon CMOS, contain
RFIN
2 3 4
VCC1
VCC2
VREF
NeW
Skyworks offers lead (Pb)-free, RoHS (Restriction of Hazardous Substances)-compliant packaging.
Package Diagram
8 7 5
GND
GND
GND
6
GND
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com
200510 Rev. H * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * February 18, 2009
1
Data Sheet * SKY65116
Operating Characteristics
VCC1, VCC2, VREF, VCNT = 3.6 V, TC = 25 C, ZO = 50 W, unless otherwise specified
Parameter Frequency Quiescent current Small signal gain Input return loss Output return loss Output power Power added efficiency Output IP3 Noise figure Thermal resistance symbol F ICQ G lS11l lS22l POUT PAE OIP3 NF QJC No RF PIN = -15 dBm PIN = -15 dBm PIN = -15 dBm @ P1 dB POUT @ P1 dB POUT = 25 dBm/tone PIN = -15 dBm Junction to case Condition Min 390 0.1 33.5 10 4.5 31.5 35 38 0.33 35 22 6 32.5 42 43 6 17.6 7.5 typ Max 500 0.375 Units MHz A dB dB dB dBm % dBm dB C/W
Absolute Maximum Ratings
Characteristic RF output power Supply voltage (VCC, VREF, VCNT ) Supply current (ICC) Power dissipation (PDISS) Operating case temperature (TC) Storage temperature (TST) Junction temperature (TJ) Value 34.5 dBm 4.5 V 1300 mA 3.7 W -40 C to +85 C -55 C to +125 C 150 C
Performance is guaranteed only under the conditions listed in the specifications table and is not guaranteed under the full range(s) described by the Absolute Maximum specifications. Exceeding any of the absolute maximum/minimum specifications may result in permanent damage to the device and will void the warranty. Each absolute maximum rating listed is an individual parameter. Biasing and driving the amplifier with more than one absolute maximum rating listed may result in permanent damage to the device. Exposure to maximum rating conditions for extended periods may reduce device reliability.
CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be employed at all times.
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 2
February 18, 2009 * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * 200510 Rev. H
Data Sheet * SKY65116
Recommended Operating Conditions
Parameter Supply voltage Reference voltage Control voltage (power up) Control voltage (power down) Operating frequency Operating case temperature symbol VCC VREF VCNT VCNT FO TC 390 -40 +25 Min. 3.2 3.2 2.7 typ. 3.6 3.6 3.6 0 0.5 500 +85 Max. 4 4 Unit V V V V MHz C
Typical Performance Data
VCC1, VCC2, VREF, VCNT = 3.6 V, TC = 25 C, ZO = 50 W, unless otherwise specified
37 36 44 -40 C 25 C 85 C 46 -40 C 25 C 85 C
OIP3 (dBm)
35
Gain (dB)
34 33
42
40 32 31 390 400 410 420 430 440 450 460 470 480 490 500 38 15 17 19 21 23 25 27 29 31 33 35
Frequency (MHz)
POUT/Tone (dBm)
Gain vs. Frequency across temperature
35.5 35.0 3.2 V 3.6 V 4.0 V 46 44
OIP3 vs. POUt/tone across temperature
3.2 V 3.6 V 4.0 V
34.0 33.5 33.0 32.5
OIP3 (dBm)
34.5
Gain (dB)
42 40 38 36
390 400 410 420 430 440 450 460 470 480 490 500
20
22
24
26
28
30
32
Frequency (MHz)
POUT/Tone (dBm)
Gain vs. Frequency across Voltage
OIP3 vs. POUt/tone across Voltage
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com
200510 Rev. H * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * February 18, 2009
3
Data Sheet * SKY65116
Typical Performance Data
VCC1, VCC2, VREF, VCNT = 3.6 V, TC = 25 C, ZO = 50 W, unless otherwise specified
0.36 0.35 0.34 0.33 46 3.2 V 3.6 V 4.0 V 50 390 MHz 450 MHz 500 MHz
OIP3 (dBm)
-15 10 35 60 85
ICQ (A)
0.32 0.31 0.30 0.29 -40
42
38
34
15
17
19
21
23
25
27
29
Temperature (C)
ICQ vs. temperature across Voltage
-40 C 25 C 85 C
POUT/Tone (dBm)
OIP3 vs. POUt/tone across Frequency
3.2 V 3.6 V 4.0 V
-12
-12
-15
-15
S11 (dB)
-18
S11 (dB)
390 400 410 420 430 440 450 460 470 480 490 500
-18
-21
-21
-24
-24
390 400 410 420 430 440 450 460 470 480 490 500
Frequency (MHz)
Frequency (MHz)
s11 vs. Frequency across temperature
-40 C 25 C 85 C -5.0
s11 vs. Frequency across VCC
3.2 V 3.6 V 4.0 V
-5.0
-5.5
-5.5
S22 (dB)
S22 (dB)
390 400 410 420 430 440 450 460 470 480 490 500
-6.0
-6.0
-6.5
-6.5
-7.0
-7.0
390 400 410 420 430 440 450 460 470 480 490 500
Frequency (MHz)
Frequency (MHz)
s22 vs. Frequency across temperature
s22 vs. Frequency across VCC
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 4
February 18, 2009 * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * 200510 Rev. H
Data Sheet * SKY65116
Typical Performance Data
VCC1, VCC2, VREF, VCNT = 3.6 V, TC = 25 C, ZO = 50 W, unless otherwise specified
7.5 7.0 -40 C 25 C 85 C 7.0 6.8 3.2 V 3.6 V 4.0 V
Noise Figure (dB)
6.5 6.0 5.5 5.0
Noise Figure (dB)
390 400 410 420 430 440 450 460 470 480 490 500
6.6 6.4 6.2 6.0 5.8
390 400 410 420 430 440 450 460 470 480 490 500
Frequency (MHz)
Frequency (MHz)
NF vs. Frequency across temperature
-40 C 50 42 34 26 18 10 25 C 85 C
NF vs. Frequency across VCC
1.8 1.6 1.4 -40 C 25 C 85 C
PAE (%)
ICC (A)
1.2 1.0 0.8 0.6 0.4
23
25
27
29
31
33
35
23
25
27
29
31
33
35
POUT (dBm)
POUT (dBm)
Pae vs. POUt across temperature
3.2 V 3.6 V 4.0 V
ICC vs. POUt across temperature
3.2 V 3.6 V 4.0 V
52 46 40
1.6 1.4 1.2
PAE (%)
ICC (A)
34 28 22 16 10 23 25 27 29 31 33 35
1.0 0.8 0.6 0.4 23 25 27 29 31 33 35
POUT (dBm)
POUT (dBm)
Pae vs. POUt across VCC
ICC vs. POUt across VCC
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com
200510 Rev. H * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * February 18, 2009
5
Data Sheet * SKY65116
Typical Performance Data
VCC1, VCC2, VREF, VCNT = 3.6 V, TC = 25 C, ZO = 50 W, unless otherwise specified
390 MHz 48 40 450 MHz 500 MHz 1.8 1.6 1.4 390 MHz 450 MHz 500 MHz
PAE (%)
ICC (A)
22 24 26 28 30 32 34 36
32 24 16 8
1.2 1.0 0.8 0.6 0.4 21 23 25 27 29 31 33 35
POUT (dBm)
POUT (dBm)
Pae vs. POUt across Frequency
-40 C 38 37 36 25 C 85 C
ICC vs. POUt across Frequency
3.2 V 3.6 V 4.0 V
36 35 34
Gain (dB)
35 34 33 32 31 21 23 25 27 29 31 33 35
Gain (dB) POUT (dBm)
33 32 31 30 23 24 25 26 27 28 29 30 31 32 33 34 35
POUT (dBm)
Gain vs. POUt across temperature
390 MHz 450 MHz 500 MHz S11
Gain vs. POUt across VCC
S21 S22
36 35
40 30 20 10
SIJ Mag (dB)
21 23 25 27 29 31 33 35
34
Gain (dB)
0 -10 -20 -30 -40 -50 -60 300 350 400 450 500 550 600
33 32 31 30
POUT (dBm)
Frequency (MHz)
Gain vs. POUt across Frequency
s-Parameters vs. Frequency
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 6
February 18, 2009 * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * 200510 Rev. H
Data Sheet * SKY65116
Typical Performance Data
VCC1, VCC2, VREF, VCNT = 3.6 V, TC = 25 C, ZO = 50 W, unless otherwise specified
350 MHz 500 MHz 400 MHz 550 MHz 450 MHz 34 33 32
36 35 33 34 32 31 30 29 28 27 26 0
P1 dB (dBm)
31 30 29 28 27 26 300 350 400 450 500 550 600
Gain (dB)
5
10
15
20
25
30
35
Frequency (MHz)
Power Out (dBm)
P1 dB vs. Frequency
Gain vs. CW Power Out
350 MHz 500 MHz 400 MHz 550 MHz 450 MHz 45 40 35
48 46 44 42 40 38 36 34 32 30 15
PAE (%)
OIP3 (dBm)
30 25 20 15 300
350
400
450
500
550
600
16
17
18
19
20
21
22
Frequency (MHz)
Power Out/Tone (dBm)
Pae @ P1 dB vs. Frequency
OIP3 vs. POUt/tone across Frequency tone Spacing =1 Mhz
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com
200510 Rev. H * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * February 18, 2009
7
Data Sheet * SKY65116
DC/RF Response Time
VCC1, VCC2, VREF = 3.6 V, VCNT = 0/3.6 V, TA = 25 C unless otherwise specified
DC Pulse (VCNT)
RF Pulse
Pulse RF-RF DC-RF RF-RF DC-RF
% 10-90 50-90 90-10 50-10
Label P3 P4 P5 P6
Rise/Fall Rise Rise Fall Fall
time 1.13 s 13.45 s 0.034 s 3.66 s
10 F capacitor, C2 and 0.01 F capacitor, C5 removed for rise-fall time measurements. Their purpose is to filter DC noise < 200 MHz due to long bias leads to power supply. No noise observed with the removal of C2 and C5.
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 8
February 18, 2009 * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * 200510 Rev. H
Data Sheet * SKY65116
Theory of Operation
The SKY65116 is comprised of two amplifier stages, and is internally matched for optimum linearity and efficiency. The matching circuits for the input stage, inter-stage, and output stage are contained within the device. An on-chip active bias circuit is included within the device for both input and output stages providing for excellent gain tracking over temperature and voltage variations. The module operates with all positive DC voltages while maintaining high efficiency and good linearity. The nominal operating voltage is 3.6 V for maximum power, but can be operated at slightly lower voltages for other mobile applications. The input and output stages are independently supplied using the VCC1 and VCC2 supply lines, pins 4 and 10, respectively. The bias reference voltage is supplied using a common VREF (pin 12) line. The module includes a silicon CMOS controller circuit to provide an amplifier On/Off operation. VCNT (pin 11) is the PA on/ off control voltage to the CMOS controller for stages 1 and 2. 0 V = Off, 3.6 V = On. Nominal "On" operating range is between 2.7 to 3.6 VDC. VCNT set to 0 VDC will force the amplifier into off mode, drawing only microamperes of current.
RF_OUt (Pin 8). Amplifier RF Output Pin. ZO = 50 W. The module includes an onboard internal DC blocking capacitor. All impedance matching is provided internal to the module. VCC2 (Pin 10). Supply voltage for the output (final) stage collector bias (typically 3.6 V). Bypassing of VCC2 is accomplished with C1 and C4 and should be placed in the approximate location shown on the evaluation board, but placement is not critical. VCNt (Pin 11). VCNT is the PA on/off control voltage to the silicon CMOS controller for stages 1 and 2. 0 V = Off, 3.6 V = On. Nominal "On" operating range is between 2.7 to 3.6 VDC. VCNT set to 0 VDC will force the amplifier into standby mode. VReF (Pin 12). Bias reference voltage for amplifier stages 1 and 2. VREF should be operated over the same voltage range as VCC, with a nominal voltage of 3.6 V.
Package and Handling Information
Since the device package is sensitive to moisture absorption, it is baked and vacuum packed before shipping. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. Please refer to Skyworks solder reflow application note, available at www.skyworksinc.com, for instructions on mounting the SKY65116 to a printed circuit board. Production quantities of this product are shipped in a standard tape and reel format. For packaging details, refer to the Skyworks Application Note, Tape and Reel, document number 101568.
Application Circuit Notes
Center Ground. It is extremely important that the device paddle be sufficiently grounded for both thermal and stability reasons. Multiple small vias are acceptable and will work well under the device if solder migration is an issue. Ground (Pins 1, 3, 5, 6, 7, 9). Attach all ground pins to the RF ground plane with the largest diameter and lowest inductance via that the layout will allow. Multiple small vias are also acceptable and will work well under the device if solder migration is an issue. RF_IN (Pin 2). Amplifier RF Input Pin. ZO = 50 W. The module includes an onboard internal DC blocking capacitor. All impedance matching is provided internal to the module. VCC1 (Pin 4). Supply voltage for the first stage collector bias (typically 3.6 V). Bypassing of VCC1 is accomplished with C7 and C8 and should be placed in the approximate location shown on the evaluation board, but placement is not critical.
Electrostatic Discharge (ESD) Sensitivity
The SKY65116 is a static-sensitive electronic device. Do not operate or store near strong electrostatic fields. Take proper ESD precautions.
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com
200510 Rev. H * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * February 18, 2009
9
Data Sheet * SKY65116
Application Circuit
Reference Voltage C3 10 F C6 0.01 F C5 0.01 F C2 10 F PA Control Voltage
VCC 12 VREF 11 VCNT 10 VCC2 C4 0.01 F C1 10 F
1
GND
GND
9
RF in 50 transmission line
2
RFIN
RFOUT
8 50 transmission line
RF out
3
GND VCC1 GND GND
GND
7
4 VCC C7 10 F C8 0.01 F
5
6
Pin Assignments
Pin # 1 2 3 4 5 6 7 8 9 10 11 12 Name GND RFIN GND VCC1 GND GND GND RFOUT GND VCC2 VCNT VREF Ground RF input Ground Stage 1 collector voltage Ground Ground Ground RF output Ground Stage 2 collector voltage PA on/off coltrol voltage Bias reference voltage description
Evaluation Board Description
The Skyworks SKY65116 evaluation board is used to test the performance of the SKY65116 power amplifier module. The following design considerations are general in nature and must be followed regardless of final use or configuration. 1. Paths to ground should be made as short as possible. 2. The ground pad of the SKY65116 power amplifier module has special electrical and thermal grounding requirements. This pad is the main thermal conduit for heat dissipation. Since the circuit board acts as the heat sink, it must shunt as much heat as possible from the amplifiers. As such, design the connection to the ground pad to dissipate the maximum wattage produced to the circuit. Multiple vias to the grounding layer are required. 3. Two external output bypass capacitors (0.01 F and 10 F) are required on the VCC1 (pin 4) supply input. The same two capacitor values are also required on the VCC2 (pin 10) supply input and on the VREF input (pin 12). Each of these capacitors should be placed in parallel between the supply line and ground. 4. VCC1 (pin 4) and VCC2 (pin 10) may be connected together at the supply. NOTE: Junction temperature (TJ) of the device increases with a poor connection to the slug and ground. This reduces the lifetime of the device.
Center attachment pad must have a low inductance and low thermal resistance connection to the customer's printed circuit board ground plane.
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 10
February 18, 2009 * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * 200510 Rev. H
Data Sheet * SKY65116
Evaluation Board Test Procedure
Use the following procedure to set up the SKY65116 evaluation board for testing: 1. Connect a 3.6 V supply to VCC1 and VCC2, and 3.6 V supply to VREF and VCNT. If available, enable the current limiting function of the VCC power supply to 1.5 A. 2. Connect a signal generator to the RF signal input port. Set it to the desired RF frequency at a power level of 2 dBm or less to the evaluation board but do NOT enable the RF signal. 3. Connect a spectrum analyzer to the RF signal output port. 4. Enable the power supply. 5. Enable the RF signal. 6. Take measurements. NOTE: It is important that the VCC1 and VCC2 voltage source be adjusted such that 3.6 V is measured at the board. The high collector currents will drop the collector voltage significantly if long leads are used. Adjust the bias voltage to compensate.
Evaluation Board Layer Detail
Layer 1: Top -- Metal
Evaluation Board
GND GND GND GND Vcc1 Vref Vcnt Vcc2 J1
Layer 2: Ground
GND GND GND GND Vcc1 Vref Vcnt Vcc2
C2 J2 C3 C6 C5 C4 J3
RFin RFIN J2
C8 C7
RFout J3 RFOUT
TW14-D620SN-
COPYRIGHT 2006 MADE IN USA
Layer 3: Ground
Recommended Solder Reflow Profiles
Refer to the "Recommended Solder Reflow Profile" Application Note.
Tape and Reel Information
Refer to the "Discrete Devices and IC Switch/Attenuators Tape and Reel Package Orientation" Application Note.
Layer 4: Solid Ground Plane
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com
200510 Rev. H * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * February 18, 2009
11
Data Sheet * SKY65116
Bill of Material for Evaluation Board
Part 1 2 Id C1, C2, C3, C7 C4, C5, C6, C8 Qty 4 4 size 1206 0402 Value 10 10000 Units F pF Manufacturer AVX Murata Product Number TAJA106M006R GRM155R71C103KA01
Evaluation Board Stack-Up
Cross Section
Name
Pri Die 1 L2
Branding Specifications
Type
Electrical Isolation Plane
Thick
0.035 mm 0.4 mm 0.035 mm
Material
Cu Rogers 4003 CU
r
0.0 3.38 0.0
Mark Pin 1 Identifier
Manufacturing Part Number Revision Number
Die 2
Isolation
0.6 mm
FR4
4.0
L3 Die 3 Sec
Plane Isolation Electrical
0.035 mm 0.4 mm 0.035 mm
CU FR4 CU
0.0 4.0 0.0
SKY65116-21 EXXXXX.XX YYWW MX
Lot Number YY = Manufacture Year WW = Week Packaged Sealed MX = Country Code
Tape and Reel Dimensions
12.00 1.10 Pin 1 4.00 0.10 B O1.50 0.10 2.00 0.10 1.75 0.10
0.318 0.013T
8.88 0.10 (Bo)
5 Max.
B O1.50 + 0.25 2.14 0.10 (Ko) 8 Max. Section B-B 8.89 0.10(Ao) Section A-A
Notes:
1. 2. 3. 4. 5. 6.
Carrier tapes must meet all requirements of Skyworks GP01-D232 procurement spec for tape and reel shipping. Carrier tape shall be black conductive polycarbonate or polystyrene. Cover tape shall be transparent conductive pressure sensitive adhesive (PSA) material w/ 13.3 mm width. ESD-surface resistivity shall be < / =1 X 108 ohms/square per EIA, JEDEC TNR speci cation. All dimensions are in milimeter Part no.: US039321 (Please indicate on purchase order)
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 12
February 18, 2009 * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * 200510 Rev. H
16.00 + 0.30 16.00 - 0.10
A
A
7.50 0.10
Data Sheet * SKY65116
Package Outline and Recommended Footprint
8.685 mm
Pin 1 Indicator
8.385
2X 1.65 mm
12X 0.81 mm 12X 1.043 mm
8.385
Top
2X 1.91mm 8.685 mm Stencil Aperture Size of 60 to 80% of the Module/Pkg Solder Mask Area
C L
1.45 0.1 (3.4) Pin 12 (O0.3) Solder Mask Opening (O0.15) Metal Pad Pin 1 Indicator
Package Outline
Stencil Aperture Top View 8.685 mm 6X 0.81 mm 1.65 mm Typ. 0.3 mm Typ.
6X 4.093
12X SMT Pad 0 4X 1.91 6X 4.093 Package Outline 0 4X 1.65 5.080 Solder Mask Opening Pin 1 A
8.685 mm
Pin 12 Package Outline 6X 1.043 mm Pin 1
(2.7)
0.3 mm Typ.
1.91 mm Typ. 0.25 mm Thermal Via Array 0.25 mm O0.3 mm On 0.6 mm Pitch Additional Vias in Common Ground Pad Will Improve Thermal Performance
C L
0.6 mm Typ. 0.6 mm Typ.
0.793 0.1 Metal Pad Edge (0.1) 0.81 0.05 Detail A
Metallization Top View 8.785 mm 1.65 mm Pin 12 12X 1.143 mm 12X 0.91 mm
C L
Pin 1
1.91mm Typ.
8.785 mm
Package Outline
5.080 Solder Mask Opening Solder Mask Opening Top View
C L
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com
200510 Rev. H * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * February 18, 2009
13
Data Sheet * SKY65116
Ordering Information
Model Name SKY65116: 390-500 MHz linear power amplifier Manufacturing Part Number SKY65116-21 (Pb-free package) evaluation Kit Part Number TW14-D621
Copyright (c) 2008, 2009, Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. ("Skyworks") products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks, the Skyworks symbol, and "Breakthrough Simplicity" are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference.
Skyworks Solutions, Inc. * Phone [781] 376-3000 * Fax [781] 376-3100 * sales@skyworksinc.com * www.skyworksinc.com 14
February 18, 2009 * Skyworks Proprietary Information * Products and Product Information are Subject to Change Without Notice. * 200510 Rev. H

▲Up To Search▲

Price & Availability of SKY65116

	To Download SKY65116 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .